viking dishwasher not draining

Top 4 Reasons for a Viking Dishwasher Not Draining Water

Even a Viking-brand dishwasher can fall victim to the draining issues common to this hard-working appliance. Why is my Viking dishwasher not draining water? The filter may be clogged with debris, requiring a thorough cleaning. Determine the 4 most likely reasons for Viking dishwasher draining problems and how to solve them.

Troubleshooting a Viking Dishwasher Not Draining Water

Given the brand’s high-quality reputation, a Viking dishwasher not draining water is usually resolved with a simple fix or more consistent maintenance. Use these Viking dishwasher troubleshooting tips to rectify draining issues.

#1. Viking Dishwasher Filter is Dirty

A dirty filter is often responsible when your Viking dishwasher won’t drain. The filter screens out large food particles to prevent them from clogging the drain pump. However, the filter itself will clog if not cleaned regularly. When this happens, water can’t drain through the filter and accumulates in the wash tub. Most dishwasher cleaning tips recommend cleaning the filter on a monthly basis to prevent clogs.

Viking dishwasher won't drain

Here’s how to clean a Viking dishwasher filter:

  1. Take out the bottom rack.
  2. Squeeze the tabs on either side of the coarse filter and lift up to remove.
  3. Twist the fine filter counterclockwise and lift upward.
  4. Rinse both components separately under running water. Gently scrub lingering debris with a soft bristle brush.
  5. Replace the fine filter and twist clockwise to secure.
  6. Push the coarse filter down until the tabs click in place.

#2. Dishwasher Drain Hose is Clogged

Wondering why there’s standing water in my dishwasher? Large food particles that bypass the filter and drain pump can clog the drain hose, resulting in a Viking dishwasher not draining water. These blockages most often occur where the hose connects to the dishwasher or the disposal or sink drain. While removing the blockage should solve the problem, this complex job is best reserved for a professional technician or an experienced DIYer.

Follow these steps to remove drain hose clogs:

  1. Unplug the dishwasher.
  2. Consult your user manual to determine the exact location of the drain hose. Most are located behind a lower front panel.
  3. Disconnect the hose from the drain pump.
  4. Inspect the hose and remove any visible blockages.
  5. If none are visible, disconnect the hose from the disposal or sink drain to look for clogs.
  6. If the obstruction can’t be reached, the hose must be replaced.

#3. Air Gap or Garbage Disposal Issues

If you have a garbage disposal or air gap it likely shares a common drain with your dishwasher. If the disposal or air gap becomes filled with debris, it often settles in this shared drain. You’ll find your Viking dishwasher not draining water if the drain becomes obstructed. In many instances, the water backs up into the wash tub, often resulting in a leaking dishwasher.

Running the disposal before starting a dishwasher cycle can eliminate any accumulated debris, leaving adequate room for water to flow. For those kitchens with an air gap, regular cleanings will prevent a buildup of debris that blocks the drain. Simply take off the air gap’s cap and scoop away any food particles and grime with a paper towel.

#4. Viking Dishwasher Drain Pump Has Failed

If your Viking dishwasher drain problem persists, it’s possible that the drain pump has failed. The pump uses an impeller to push water out of the dishwasher and through the drain hose. If the pump motor fails or another component is defective, water will remain in the dishwasher. 

standing water in my dishwasher

If the pump motor shows a lack of continuity with multimeter testing or the pump won’t run, it requires professional replacement.

For the very best Viking dishwasher repair in Minneapolis, look no further than D&T Appliance Service. Schedule your service with our expert technicians today!

You might also like...

subscribe & save on appliance repair

$10 Off